Discussion:
(unknown)
m***@acm.org
2014-10-07 19:27:11 UTC
Permalink
I'm dealing with issues with bad backtraces in MIPS kdumps. This
patch series fixes the issues with these backtraces.

Note that this does not currently enable DWARF unwinding on the
restore side. It's less useful (unless you have a backtrace that
runs through the restore code). It could be done, I think,
without major hassle, but I'll save that for future assuming
these sorts of changes are ok.

Those moves a lot of generic stuff from the x86 dwarf2.h to a new
asm-generic version, but does not make any functional changes to
that code.
m***@acm.org
2014-10-07 19:27:12 UTC
Permalink
From: Corey Minyard <***@mvista.com>

The MIPS frame save code was just saving a few registers, enough to
do a backtrace if every function set up a frame. However, this is
not working if you are using DWARF unwinding, because most of the
registers are wrong. This was causing kdump backtraces to be short
or bogus.

So save all the registers.

Signed-off-by: Corey Minyard <***@mvista.com>
---
arch/mips/include/asm/stacktrace.h | 64 +++++++++++++++++++++++++++++---------
1 file changed, 50 insertions(+), 14 deletions(-)

diff --git a/arch/mips/include/asm/stacktrace.h b/arch/mips/include/asm/stacktrace.h
index 780ee2c..10c4e9c 100644
--- a/arch/mips/include/asm/stacktrace.h
+++ b/arch/mips/include/asm/stacktrace.h
@@ -2,6 +2,8 @@
#define _ASM_STACKTRACE_H

#include <asm/ptrace.h>
+#include <asm/asm.h>
+#include <linux/stringify.h>

#ifdef CONFIG_KALLSYMS
extern int raw_show_trace;
@@ -20,6 +22,14 @@ static inline unsigned long unwind_stack(struct task_struct *task,
}
#endif

+#define STR_PTR_LA __stringify(PTR_LA)
+#define STR_LONG_S __stringify(LONG_S)
+#define STR_LONG_L __stringify(LONG_L)
+#define STR_LONGSIZE __stringify(LONGSIZE)
+
+#define STORE_ONE_REG(r) \
+ STR_LONG_S " $" __stringify(r)",("STR_LONGSIZE"*"__stringify(r)")(%1)\n\t"
+
static __always_inline void prepare_frametrace(struct pt_regs *regs)
{
#ifndef CONFIG_KALLSYMS
@@ -32,21 +42,47 @@ static __always_inline void prepare_frametrace(struct pt_regs *regs)
__asm__ __volatile__(
".set push\n\t"
".set noat\n\t"
-#ifdef CONFIG_64BIT
- "1: dla $1, 1b\n\t"
- "sd $1, %0\n\t"
- "sd $29, %1\n\t"
- "sd $31, %2\n\t"
-#else
- "1: la $1, 1b\n\t"
- "sw $1, %0\n\t"
- "sw $29, %1\n\t"
- "sw $31, %2\n\t"
-#endif
+ /* Store $1 so we can use it */
+ STR_LONG_S " $1,"STR_LONGSIZE"(%1)\n\t"
+ /* Store the PC */
+ "1: " STR_PTR_LA " $1, 1b\n\t"
+ STR_LONG_S " $1,%0\n\t"
+ STORE_ONE_REG(2)
+ STORE_ONE_REG(3)
+ STORE_ONE_REG(4)
+ STORE_ONE_REG(5)
+ STORE_ONE_REG(6)
+ STORE_ONE_REG(7)
+ STORE_ONE_REG(8)
+ STORE_ONE_REG(9)
+ STORE_ONE_REG(10)
+ STORE_ONE_REG(11)
+ STORE_ONE_REG(12)
+ STORE_ONE_REG(13)
+ STORE_ONE_REG(14)
+ STORE_ONE_REG(15)
+ STORE_ONE_REG(16)
+ STORE_ONE_REG(17)
+ STORE_ONE_REG(18)
+ STORE_ONE_REG(19)
+ STORE_ONE_REG(20)
+ STORE_ONE_REG(21)
+ STORE_ONE_REG(22)
+ STORE_ONE_REG(23)
+ STORE_ONE_REG(24)
+ STORE_ONE_REG(25)
+ STORE_ONE_REG(26)
+ STORE_ONE_REG(27)
+ STORE_ONE_REG(28)
+ STORE_ONE_REG(29)
+ STORE_ONE_REG(30)
+ STORE_ONE_REG(31)
+ /* Restore $1 */
+ STR_LONG_L " $1,"STR_LONGSIZE"(%1)\n\t"
".set pop\n\t"
- : "=m" (regs->cp0_epc),
- "=m" (regs->regs[29]), "=m" (regs->regs[31])
- : : "memory");
+ : "=m" (regs->cp0_epc)
+ : "r" (regs->regs)
+ : "memory");
}

#endif /* _ASM_STACKTRACE_H */
--
1.8.3.1
m***@acm.org
2014-10-07 19:27:13 UTC
Permalink
From: Corey Minyard <***@mvista.com>

A lot of arch/x86/include/asm/dwarf2.h was generic, move it to
asm-generic so other arches can get to it.

Signed-off-by: Corey Minyard <***@mvista.com>
---
arch/x86/include/asm/dwarf2.h | 74 +----------------------------------------
include/asm-generic/dwarf2.h | 77 +++++++++++++++++++++++++++++++++++++++++++
2 files changed, 78 insertions(+), 73 deletions(-)
create mode 100644 include/asm-generic/dwarf2.h

diff --git a/arch/x86/include/asm/dwarf2.h b/arch/x86/include/asm/dwarf2.h
index f6f1598..3360e2a 100644
--- a/arch/x86/include/asm/dwarf2.h
+++ b/arch/x86/include/asm/dwarf2.h
@@ -1,79 +1,7 @@
#ifndef _ASM_X86_DWARF2_H
#define _ASM_X86_DWARF2_H

-#ifndef __ASSEMBLY__
-#warning "asm/dwarf2.h should be only included in pure assembly files"
-#endif
-
-/*
- * Macros for dwarf2 CFI unwind table entries.
- * See "as.info" for details on these pseudo ops. Unfortunately
- * they are only supported in very new binutils, so define them
- * away for older version.
- */
-
-#ifdef CONFIG_AS_CFI
-
-#define CFI_STARTPROC .cfi_startproc
-#define CFI_ENDPROC .cfi_endproc
-#define CFI_DEF_CFA .cfi_def_cfa
-#define CFI_DEF_CFA_REGISTER .cfi_def_cfa_register
-#define CFI_DEF_CFA_OFFSET .cfi_def_cfa_offset
-#define CFI_ADJUST_CFA_OFFSET .cfi_adjust_cfa_offset
-#define CFI_OFFSET .cfi_offset
-#define CFI_REL_OFFSET .cfi_rel_offset
-#define CFI_REGISTER .cfi_register
-#define CFI_RESTORE .cfi_restore
-#define CFI_REMEMBER_STATE .cfi_remember_state
-#define CFI_RESTORE_STATE .cfi_restore_state
-#define CFI_UNDEFINED .cfi_undefined
-#define CFI_ESCAPE .cfi_escape
-
-#ifdef CONFIG_AS_CFI_SIGNAL_FRAME
-#define CFI_SIGNAL_FRAME .cfi_signal_frame
-#else
-#define CFI_SIGNAL_FRAME
-#endif
-
-#if defined(CONFIG_AS_CFI_SECTIONS) && defined(__ASSEMBLY__)
- /*
- * Emit CFI data in .debug_frame sections, not .eh_frame sections.
- * The latter we currently just discard since we don't do DWARF
- * unwinding at runtime. So only the offline DWARF information is
- * useful to anyone. Note we should not use this directive if this
- * file is used in the vDSO assembly, or if vmlinux.lds.S gets
- * changed so it doesn't discard .eh_frame.
- */
- .cfi_sections .debug_frame
-#endif
-
-#else
-
-/*
- * Due to the structure of pre-exisiting code, don't use assembler line
- * comment character # to ignore the arguments. Instead, use a dummy macro.
- */
-.macro cfi_ignore a=0, b=0, c=0, d=0
-.endm
-
-#define CFI_STARTPROC cfi_ignore
-#define CFI_ENDPROC cfi_ignore
-#define CFI_DEF_CFA cfi_ignore
-#define CFI_DEF_CFA_REGISTER cfi_ignore
-#define CFI_DEF_CFA_OFFSET cfi_ignore
-#define CFI_ADJUST_CFA_OFFSET cfi_ignore
-#define CFI_OFFSET cfi_ignore
-#define CFI_REL_OFFSET cfi_ignore
-#define CFI_REGISTER cfi_ignore
-#define CFI_RESTORE cfi_ignore
-#define CFI_REMEMBER_STATE cfi_ignore
-#define CFI_RESTORE_STATE cfi_ignore
-#define CFI_UNDEFINED cfi_ignore
-#define CFI_ESCAPE cfi_ignore
-#define CFI_SIGNAL_FRAME cfi_ignore
-
-#endif
-
+#include <asm-generic/dwarf2.h>
/*
* An attempt to make CFI annotations more or less
* correct and shorter. It is implied that you know
diff --git a/include/asm-generic/dwarf2.h b/include/asm-generic/dwarf2.h
new file mode 100644
index 0000000..19a677f
--- /dev/null
+++ b/include/asm-generic/dwarf2.h
@@ -0,0 +1,77 @@
+#ifndef _ASM_GENERIC_DWARF2_H
+#define _ASM_GENERIC_DWARF2_H
+
+#ifndef __ASSEMBLY__
+#warning "asm/dwarf2.h should be only included in pure assembly files"
+#endif
+
+/*
+ * Macros for dwarf2 CFI unwind table entries.
+ * See "as.info" for details on these pseudo ops. Unfortunately
+ * they are only supported in very new binutils, so define them
+ * away for older version.
+ */
+
+#ifdef CONFIG_AS_CFI
+
+#define CFI_STARTPROC .cfi_startproc
+#define CFI_ENDPROC .cfi_endproc
+#define CFI_DEF_CFA .cfi_def_cfa
+#define CFI_DEF_CFA_REGISTER .cfi_def_cfa_register
+#define CFI_DEF_CFA_OFFSET .cfi_def_cfa_offset
+#define CFI_ADJUST_CFA_OFFSET .cfi_adjust_cfa_offset
+#define CFI_OFFSET .cfi_offset
+#define CFI_REL_OFFSET .cfi_rel_offset
+#define CFI_REGISTER .cfi_register
+#define CFI_RESTORE .cfi_restore
+#define CFI_REMEMBER_STATE .cfi_remember_state
+#define CFI_RESTORE_STATE .cfi_restore_state
+#define CFI_UNDEFINED .cfi_undefined
+#define CFI_ESCAPE .cfi_escape
+
+#ifdef CONFIG_AS_CFI_SIGNAL_FRAME
+#define CFI_SIGNAL_FRAME .cfi_signal_frame
+#else
+#define CFI_SIGNAL_FRAME
+#endif
+
+#if defined(CONFIG_AS_CFI_SECTIONS) && defined(__ASSEMBLY__)
+ /*
+ * Emit CFI data in .debug_frame sections, not .eh_frame sections.
+ * The latter we currently just discard since we don't do DWARF
+ * unwinding at runtime. So only the offline DWARF information is
+ * useful to anyone. Note we should not use this directive if this
+ * file is used in the vDSO assembly, or if vmlinux.lds.S gets
+ * changed so it doesn't discard .eh_frame.
+ */
+ .cfi_sections .debug_frame
+#endif
+
+#else
+
+/*
+ * Due to the structure of pre-exisiting code, don't use assembler line
+ * comment character # to ignore the arguments. Instead, use a dummy macro.
+ */
+.macro cfi_ignore a=0, b=0, c=0, d=0
+.endm
+
+#define CFI_STARTPROC cfi_ignore
+#define CFI_ENDPROC cfi_ignore
+#define CFI_DEF_CFA cfi_ignore
+#define CFI_DEF_CFA_REGISTER cfi_ignore
+#define CFI_DEF_CFA_OFFSET cfi_ignore
+#define CFI_ADJUST_CFA_OFFSET cfi_ignore
+#define CFI_OFFSET cfi_ignore
+#define CFI_REL_OFFSET cfi_ignore
+#define CFI_REGISTER cfi_ignore
+#define CFI_RESTORE cfi_ignore
+#define CFI_REMEMBER_STATE cfi_ignore
+#define CFI_RESTORE_STATE cfi_ignore
+#define CFI_UNDEFINED cfi_ignore
+#define CFI_ESCAPE cfi_ignore
+#define CFI_SIGNAL_FRAME cfi_ignore
+
+#endif
+
+#endif /* _ASM_GENERIC_DWARF2_H */
--
1.8.3.1
m***@acm.org
2014-10-07 19:27:14 UTC
Permalink
From: Corey Minyard <***@mvista.com>

This will allow kdump dumps and kgdb to work correctly
with MIPS.

Signed-off-by: Corey Minyard <***@mvista.com>
---
arch/mips/Makefile | 14 ++-
arch/mips/include/asm/asm.h | 13 +-
arch/mips/include/asm/dwarf2.h | 6 +
arch/mips/include/asm/stackframe.h | 245 +++++++++++++++++++++----------------
arch/mips/kernel/entry.S | 2 +-
arch/mips/kernel/genex.S | 21 ++--
arch/mips/mm/tlbex-fault.S | 7 +-
7 files changed, 187 insertions(+), 121 deletions(-)
create mode 100644 arch/mips/include/asm/dwarf2.h

diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index bbac51e1..6a76ee6 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -238,11 +238,23 @@ ifdef CONFIG_64BIT
endif
endif

-KBUILD_AFLAGS += $(cflags-y)
+
+# do binutils support CFI?
+cfireg := $$$$0
+cfi := $(call as-instr,.cfi_startproc\n.cfi_rel_offset $(cfireg)$(comma)0\n.cfi_endproc,-DCONFIG_AS_CFI=1)
+# is .cfi_signal_frame supported too?
+cfi-sigframe := $(call as-instr,.cfi_startproc\n.cfi_signal_frame\n.cfi_endproc,-DCONFIG_AS_CFI_SIGNAL_FRAME=1)
+cfi-sections := $(call as-instr,.cfi_sections .debug_frame,-DCONFIG_AS_CFI_SECTIONS=1)
+
+KBUILD_AFLAGS += $(cfi) $(cfi-sigframe) $(cfi-sections) $(cflags-y)
KBUILD_CFLAGS += $(cflags-y)
KBUILD_CPPFLAGS += -DVMLINUX_LOAD_ADDRESS=$(load-y)
KBUILD_CPPFLAGS += -DDATAOFFSET=$(if $(dataoffset-y),$(dataoffset-y),0)

+# This is required to get dwarf unwinding tables into .debug_frame
+# instead of .eh_frame so we don't discard them.
+KBUILD_CFLAGS += -fno-asynchronous-unwind-tables
+
bootvars-y = VMLINUX_LOAD_ADDRESS=$(load-y) \
VMLINUX_ENTRY_ADDRESS=$(entry-y)

diff --git a/arch/mips/include/asm/asm.h b/arch/mips/include/asm/asm.h
index 7c26b28..8eb79862 100644
--- a/arch/mips/include/asm/asm.h
+++ b/arch/mips/include/asm/asm.h
@@ -19,6 +19,9 @@

#include <asm/sgidefs.h>
#include <asm/asm-eva.h>
+#ifdef __ASSEMBLY__
+#include <asm/dwarf2.h>
+#endif

#ifndef CAT
#ifdef __STDC__
@@ -54,7 +57,9 @@
.align 2; \
.type symbol, @function; \
.ent symbol, 0; \
-symbol: .frame sp, 0, ra
+symbol: .frame sp, 0, ra; \
+ CFI_STARTPROC
+

/*
* NESTED - declare nested routine entry point
@@ -63,13 +68,15 @@ symbol: .frame sp, 0, ra
.globl symbol; \
.align 2; \
.type symbol, @function; \
- .ent symbol, 0; \
-symbol: .frame sp, framesize, rpc
+ .ent symbol, 0; \
+symbol: .frame sp, framesize, rpc; \
+ CFI_STARTPROC

/*
* END - mark end of function
*/
#define END(function) \
+ CFI_ENDPROC; \
.end function; \
.size function, .-function

diff --git a/arch/mips/include/asm/dwarf2.h b/arch/mips/include/asm/dwarf2.h
new file mode 100644
index 0000000..1728acd
--- /dev/null
+++ b/arch/mips/include/asm/dwarf2.h
@@ -0,0 +1,6 @@
+#ifndef _ASM_MIPS_DWARF2_H
+#define _ASM_MIPS_DWARF2_H
+
+#include <asm-generic/dwarf2.h>
+
+#endif /* _ASM_MIPS_DWARF2_H */
diff --git a/arch/mips/include/asm/stackframe.h b/arch/mips/include/asm/stackframe.h
index b188c79..0976f03 100644
--- a/arch/mips/include/asm/stackframe.h
+++ b/arch/mips/include/asm/stackframe.h
@@ -18,6 +18,30 @@
#include <asm/mipsregs.h>
#include <asm/asm-offsets.h>
#include <asm/thread_info.h>
+#include <asm/dwarf2.h>
+
+/* Make the addition of cfi info a little easier. */
+ .macro cfi_rel_offset reg offset=0 docfi=0
+ .if \docfi
+ CFI_REL_OFFSET \reg, \offset
+ .endif
+ .endm
+
+ .macro cfi_st reg offset=0 docfi=0
+ LONG_S \reg, \offset(sp)
+ cfi_rel_offset \reg, \offset, \docfi
+ .endm
+
+ .macro cfi_restore reg offset=0 docfi=0
+ .if \docfi
+ CFI_RESTORE \reg
+ .endif
+ .endm
+
+ .macro cfi_ld reg offset=0 docfi=0
+ LONG_L \reg, \offset(sp)
+ cfi_restore \reg \offset \docfi
+ .endm

#if defined(CONFIG_CPU_R3000) || defined(CONFIG_CPU_TX39XX)
#define STATMASK 0x3f
@@ -25,14 +49,14 @@
#define STATMASK 0x1f
#endif

- .macro SAVE_AT
+ .macro SAVE_AT docfi=0
.set push
.set noat
- LONG_S $1, PT_R1(sp)
+ cfi_st $1, PT_R1, \docfi
.set pop
.endm

- .macro SAVE_TEMP
+ .macro SAVE_TEMP docfi=0
#ifdef CONFIG_CPU_HAS_SMARTMIPS
mflhxu v1
LONG_S v1, PT_LO(sp)
@@ -44,20 +68,20 @@
mfhi v1
#endif
#ifdef CONFIG_32BIT
- LONG_S $8, PT_R8(sp)
- LONG_S $9, PT_R9(sp)
+ cfi_st $8, PT_R8, \docfi
+ cfi_st $9, PT_R9, \docfi
#endif
- LONG_S $10, PT_R10(sp)
- LONG_S $11, PT_R11(sp)
- LONG_S $12, PT_R12(sp)
+ cfi_st $10, PT_R10, \docfi
+ cfi_st $11, PT_R11, \docfi
+ cfi_st $12, PT_R12, \docfi
#ifndef CONFIG_CPU_HAS_SMARTMIPS
LONG_S v1, PT_HI(sp)
mflo v1
#endif
- LONG_S $13, PT_R13(sp)
- LONG_S $14, PT_R14(sp)
- LONG_S $15, PT_R15(sp)
- LONG_S $24, PT_R24(sp)
+ cfi_st $13, PT_R13, \docfi
+ cfi_st $14, PT_R14, \docfi
+ cfi_st $15, PT_R15, \docfi
+ cfi_st $24, PT_R24, \docfi
#ifndef CONFIG_CPU_HAS_SMARTMIPS
LONG_S v1, PT_LO(sp)
#endif
@@ -71,16 +95,16 @@
#endif
.endm

- .macro SAVE_STATIC
- LONG_S $16, PT_R16(sp)
- LONG_S $17, PT_R17(sp)
- LONG_S $18, PT_R18(sp)
- LONG_S $19, PT_R19(sp)
- LONG_S $20, PT_R20(sp)
- LONG_S $21, PT_R21(sp)
- LONG_S $22, PT_R22(sp)
- LONG_S $23, PT_R23(sp)
- LONG_S $30, PT_R30(sp)
+ .macro SAVE_STATIC docfi=0
+ cfi_st $16, PT_R16, \docfi
+ cfi_st $17, PT_R17, \docfi
+ cfi_st $18, PT_R18, \docfi
+ cfi_st $19, PT_R19, \docfi
+ cfi_st $20, PT_R20, \docfi
+ cfi_st $21, PT_R21, \docfi
+ cfi_st $22, PT_R22, \docfi
+ cfi_st $23, PT_R23, \docfi
+ cfi_st $30, PT_R30, \docfi
.endm

#ifdef CONFIG_SMP
@@ -143,7 +167,7 @@
.endm
#endif

- .macro SAVE_SOME
+ .macro SAVE_SOME docfi=0
.set push
.set noat
.set reorder
@@ -157,16 +181,26 @@
get_saved_sp
#ifndef CONFIG_CPU_DADDI_WORKAROUNDS
8: move k0, sp
+ .if \docfi
+ CFI_REGISTER sp, k0
+ .endif
PTR_SUBU sp, k1, PT_SIZE
#else
.set at=k0
8: PTR_SUBU k1, PT_SIZE
.set noat
move k0, sp
+ .if \docfi
+ CFI_REGISTER sp, k0
+ .endif
move sp, k1
#endif
- LONG_S k0, PT_R29(sp)
- LONG_S $3, PT_R3(sp)
+ .if \docfi
+ CFI_DEF_CFA sp,0
+ .endif
+ cfi_st k0, PT_R29, \docfi
+ cfi_rel_offset sp, PT_R29, \docfi
+ cfi_st v1, PT_R3, \docfi
/*
* You might think that you don't need to save $0,
* but the FPU emulator and gdb remote debug stub
@@ -174,23 +208,26 @@
*/
LONG_S $0, PT_R0(sp)
mfc0 v1, CP0_STATUS
- LONG_S $2, PT_R2(sp)
+ cfi_st v0, PT_R2, \docfi
LONG_S v1, PT_STATUS(sp)
- LONG_S $4, PT_R4(sp)
+ cfi_st $4, PT_R4, \docfi
mfc0 v1, CP0_CAUSE
- LONG_S $5, PT_R5(sp)
+ cfi_st $5, PT_R5, \docfi
LONG_S v1, PT_CAUSE(sp)
- LONG_S $6, PT_R6(sp)
+ cfi_st $6, PT_R6, \docfi
MFC0 v1, CP0_EPC
- LONG_S $7, PT_R7(sp)
+ cfi_st $7, PT_R7, \docfi
#ifdef CONFIG_64BIT
- LONG_S $8, PT_R8(sp)
- LONG_S $9, PT_R9(sp)
+ cfi_st $8, PT_R8, \docfi
+ cfi_st $9, PT_R9, \docfi
#endif
LONG_S v1, PT_EPC(sp)
- LONG_S $25, PT_R25(sp)
- LONG_S $28, PT_R28(sp)
- LONG_S $31, PT_R31(sp)
+ .if \docfi
+ CFI_REL_OFFSET ra, PT_EPC
+ .endif
+ cfi_st $25, PT_R25, \docfi
+ cfi_st $28, PT_R28, \docfi
+ cfi_st $31, PT_R31, \docfi
ori $28, sp, _THREAD_MASK
xori $28, _THREAD_MASK
#ifdef CONFIG_CPU_CAVIUM_OCTEON
@@ -200,21 +237,21 @@
.set pop
.endm

- .macro SAVE_ALL
- SAVE_SOME
- SAVE_AT
- SAVE_TEMP
- SAVE_STATIC
+ .macro SAVE_ALL docfi=0
+ SAVE_SOME \docfi
+ SAVE_AT \docfi
+ SAVE_TEMP \docfi
+ SAVE_STATIC \docfi
.endm

- .macro RESTORE_AT
+ .macro RESTORE_AT docfi=0
.set push
.set noat
- LONG_L $1, PT_R1(sp)
+ cfi_ld $1, PT_R1, \docfi
.set pop
.endm

- .macro RESTORE_TEMP
+ .macro RESTORE_TEMP docfi=0
#ifdef CONFIG_CPU_CAVIUM_OCTEON
/* Restore the Octeon multiplier state */
jal octeon_mult_restore
@@ -233,33 +270,33 @@
mthi $24
#endif
#ifdef CONFIG_32BIT
- LONG_L $8, PT_R8(sp)
- LONG_L $9, PT_R9(sp)
+ cfi_ld $8, PT_R8, \docfi
+ cfi_ld $9, PT_R9, \docfi
#endif
- LONG_L $10, PT_R10(sp)
- LONG_L $11, PT_R11(sp)
- LONG_L $12, PT_R12(sp)
- LONG_L $13, PT_R13(sp)
- LONG_L $14, PT_R14(sp)
- LONG_L $15, PT_R15(sp)
- LONG_L $24, PT_R24(sp)
+ cfi_ld $10, PT_R10, \docfi
+ cfi_ld $11, PT_R11, \docfi
+ cfi_ld $12, PT_R12, \docfi
+ cfi_ld $13, PT_R13, \docfi
+ cfi_ld $14, PT_R14, \docfi
+ cfi_ld $15, PT_R15, \docfi
+ cfi_ld $24, PT_R24, \docfi
.endm

- .macro RESTORE_STATIC
- LONG_L $16, PT_R16(sp)
- LONG_L $17, PT_R17(sp)
- LONG_L $18, PT_R18(sp)
- LONG_L $19, PT_R19(sp)
- LONG_L $20, PT_R20(sp)
- LONG_L $21, PT_R21(sp)
- LONG_L $22, PT_R22(sp)
- LONG_L $23, PT_R23(sp)
- LONG_L $30, PT_R30(sp)
+ .macro RESTORE_STATIC docfi=0
+ cfi_ld $16, PT_R16, \docfi
+ cfi_ld $17, PT_R17, \docfi
+ cfi_ld $18, PT_R18, \docfi
+ cfi_ld $19, PT_R19, \docfi
+ cfi_ld $20, PT_R20, \docfi
+ cfi_ld $21, PT_R21, \docfi
+ cfi_ld $22, PT_R22, \docfi
+ cfi_ld $23, PT_R23, \docfi
+ cfi_ld $30, PT_R30, \docfi
.endm

#if defined(CONFIG_CPU_R3000) || defined(CONFIG_CPU_TX39XX)

- .macro RESTORE_SOME
+ .macro RESTORE_SOME docfi=0
.set push
.set reorder
.set noat
@@ -274,30 +311,30 @@
and v0, v1
or v0, a0
mtc0 v0, CP0_STATUS
- LONG_L $31, PT_R31(sp)
- LONG_L $28, PT_R28(sp)
- LONG_L $25, PT_R25(sp)
- LONG_L $7, PT_R7(sp)
- LONG_L $6, PT_R6(sp)
- LONG_L $5, PT_R5(sp)
- LONG_L $4, PT_R4(sp)
- LONG_L $3, PT_R3(sp)
- LONG_L $2, PT_R2(sp)
+ cfi_ld $31, PT_R31, \docfi
+ cfi_ld $28, PT_R28, \docfi
+ cfi_ld $25, PT_R25, \docfi
+ cfi_ld $7, PT_R7, \docfi
+ cfi_ld $6, PT_R6, \docfi
+ cfi_ld $5, PT_R5, \docfi
+ cfi_ld $4, PT_R4, \docfi
+ cfi_ld $3, PT_R3, \docfi
+ cfi_ld $2, PT_R2, \docfi
.set pop
.endm

- .macro RESTORE_SP_AND_RET
+ .macro RESTORE_SP_AND_RET docfi=0
.set push
.set noreorder
LONG_L k0, PT_EPC(sp)
- LONG_L sp, PT_R29(sp)
+ cfi_ld sp, PT_R29, \docfi
jr k0
rfe
.set pop
.endm

#else
- .macro RESTORE_SOME
+ .macro RESTORE_SOME docfi=0
.set push
.set reorder
.set noat
@@ -314,24 +351,28 @@
mtc0 v0, CP0_STATUS
LONG_L v1, PT_EPC(sp)
MTC0 v1, CP0_EPC
- LONG_L $31, PT_R31(sp)
- LONG_L $28, PT_R28(sp)
- LONG_L $25, PT_R25(sp)
+ cfi_ld $31, PT_R31, \docfi
+ cfi_ld $28, PT_R28, \docfi
+ cfi_ld $25, PT_R25, \docfi
#ifdef CONFIG_64BIT
- LONG_L $8, PT_R8(sp)
- LONG_L $9, PT_R9(sp)
+ cfi_ld $8, PT_R8, \docfi
+ cfi_ld $9, PT_R9, \docfi
#endif
- LONG_L $7, PT_R7(sp)
- LONG_L $6, PT_R6(sp)
- LONG_L $5, PT_R5(sp)
- LONG_L $4, PT_R4(sp)
- LONG_L $3, PT_R3(sp)
- LONG_L $2, PT_R2(sp)
+ cfi_ld $7, PT_R7, \docfi
+ cfi_ld $6, PT_R6, \docfi
+ cfi_ld $5, PT_R5, \docfi
+ cfi_ld $4, PT_R4, \docfi
+ cfi_ld $3, PT_R3, \docfi
+ cfi_ld $2, PT_R2, \docfi
.set pop
.endm

- .macro RESTORE_SP_AND_RET
- LONG_L sp, PT_R29(sp)
+ .macro RESTORE_SP docfi=0
+ cfi_ld sp, PT_R29, \docfi
+ .endm
+
+ .macro RESTORE_SP_AND_RET docfi=0
+ RESTORE_SP \docfi
.set arch=r4000
eret
.set mips0
@@ -339,24 +380,20 @@

#endif

- .macro RESTORE_SP
- LONG_L sp, PT_R29(sp)
- .endm
-
- .macro RESTORE_ALL
- RESTORE_TEMP
- RESTORE_STATIC
- RESTORE_AT
- RESTORE_SOME
- RESTORE_SP
+ .macro RESTORE_ALL docfi=0
+ RESTORE_TEMP \docfi
+ RESTORE_STATIC \docfi
+ RESTORE_AT \docfi
+ RESTORE_SOME \docfi
+ RESTORE_SP \docfi
.endm

- .macro RESTORE_ALL_AND_RET
- RESTORE_TEMP
- RESTORE_STATIC
- RESTORE_AT
- RESTORE_SOME
- RESTORE_SP_AND_RET
+ .macro RESTORE_ALL_AND_RET docfi=0
+ RESTORE_TEMP \docfi
+ RESTORE_STATIC \docfi
+ RESTORE_AT \docfi
+ RESTORE_SOME \docfi
+ RESTORE_SP_AND_RET \docfi
.endm

/*
diff --git a/arch/mips/kernel/entry.S b/arch/mips/kernel/entry.S
index 4353d32..6eb3b28 100644
--- a/arch/mips/kernel/entry.S
+++ b/arch/mips/kernel/entry.S
@@ -144,7 +144,7 @@ FEXPORT(syscall_exit_partial)
li t0, _TIF_ALLWORK_MASK
and t0, a2
beqz t0, restore_partial
- SAVE_STATIC
+ SAVE_STATIC docfi=0
syscall_exit_work:
LONG_L t0, PT_STATUS(sp) # returning to kernel mode?
andi t0, t0, KU_USER
diff --git a/arch/mips/kernel/genex.S b/arch/mips/kernel/genex.S
index ac35e12..68c8d34 100644
--- a/arch/mips/kernel/genex.S
+++ b/arch/mips/kernel/genex.S
@@ -151,6 +151,7 @@ LEAF(__r4k_wait)
.align 5
BUILD_ROLLBACK_PROLOGUE handle_int
NESTED(handle_int, PT_SIZE, sp)
+ CFI_SIGNAL_FRAME
#ifdef CONFIG_TRACE_IRQFLAGS
/*
* Check to see if the interrupted code has just disabled
@@ -182,18 +183,18 @@ NESTED(handle_int, PT_SIZE, sp)
1:
.set pop
#endif
- SAVE_ALL
+ SAVE_ALL docfi=1
CLI
TRACE_IRQS_OFF

LONG_L s0, TI_REGS($28)
LONG_S sp, TI_REGS($28)
- PTR_LA ra, ret_from_irq
PTR_LA v0, plat_irq_dispatch
- jr v0
+ jal v0
#ifdef CONFIG_CPU_MICROMIPS
nop
#endif
+ j ret_from_irq
END(handle_int)

__INIT
@@ -233,8 +234,8 @@ NESTED(except_vec_ejtag_debug, 0, sp)
*/
BUILD_ROLLBACK_PROLOGUE except_vec_vi
NESTED(except_vec_vi, 0, sp)
- SAVE_SOME
- SAVE_AT
+ SAVE_SOME docfi=1
+ SAVE_AT docfi=1
.set push
.set noreorder
PTR_LA v1, except_vec_vi_handler
@@ -263,8 +264,8 @@ NESTED(except_vec_vi_handler, 0, sp)

LONG_L s0, TI_REGS($28)
LONG_S sp, TI_REGS($28)
- PTR_LA ra, ret_from_irq
- jr v0
+ jal v0
+ j ret_from_irq
END(except_vec_vi_handler)

/*
@@ -322,6 +323,7 @@ NESTED(except_vec_nmi, 0, sp)
__FINIT

NESTED(nmi_handler, PT_SIZE, sp)
+ CFI_SIGNAL_FRAME
.set push
.set noat
/*
@@ -400,6 +402,7 @@ NESTED(nmi_handler, PT_SIZE, sp)
.macro __BUILD_HANDLER exception handler clear verbose ext
.align 5
NESTED(handle_\exception, PT_SIZE, sp)
+ CFI_SIGNAL_FRAME
.set noat
SAVE_ALL
FEXPORT(handle_\exception\ext)
@@ -407,8 +410,8 @@ NESTED(nmi_handler, PT_SIZE, sp)
.set at
__BUILD_\verbose \exception
move a0, sp
- PTR_LA ra, ret_from_exception
- j do_\handler
+ jal do_\handler
+ j ret_from_exception
END(handle_\exception)
.endm

diff --git a/arch/mips/mm/tlbex-fault.S b/arch/mips/mm/tlbex-fault.S
index 318855e..c91cde8 100644
--- a/arch/mips/mm/tlbex-fault.S
+++ b/arch/mips/mm/tlbex-fault.S
@@ -12,14 +12,15 @@

.macro tlb_do_page_fault, write
NESTED(tlb_do_page_fault_\write, PT_SIZE, sp)
- SAVE_ALL
+ CFI_SIGNAL_FRAME
+ SAVE_ALL docfi=1
MFC0 a2, CP0_BADVADDR
KMODE
move a0, sp
REG_S a2, PT_BVADDR(sp)
li a1, \write
- PTR_LA ra, ret_from_exception
- j do_page_fault
+ jal do_page_fault
+ j ret_from_exception
END(tlb_do_page_fault_\write)
.endm
--
1.8.3.1
Loading...