[PATCH 0/4] add mt7620n and mt7628an support

[John Crispin]

MT7620n is the small version of MT7620a with a smaller package and a few
peripherals missing. MT7628an is the new low cost version of the MT7620.

Also fix early_printk so that it allows more SoCs. MT7628an has a different irq
register layout. Make the driver load the register map from DT.


John Crispin (4):
MIPS: ralink: cleanup early_printk
MIPS: ralink: allow loading irq registers from the devicetree
MIPS: ralink: add support for MT7620n
MIPS: ralink: add mt7628an support

arch/mips/include/asm/mach-ralink/mt7620.h | 18 +-
arch/mips/ralink/Kconfig | 2 +-
arch/mips/ralink/early_printk.c | 45 +++--
arch/mips/ralink/irq.c | 34 +++-
arch/mips/ralink/mt7620.c | 282 +++++++++++++++++++++++-----
5 files changed, 305 insertions(+), 76 deletions(-)

[John Crispin]

Add support for the new MT7621/8 SoC and kill ifdefs.
Cleanup some whitespace error while we are at it.

Signed-off-by: John Crispin <***@openwrt.org>
---
arch/mips/ralink/early_printk.c | 45 ++++++++++++++++++++++++++-------------
1 file changed, 30 insertions(+), 15 deletions(-)

diff --git a/arch/mips/ralink/early_printk.c b/arch/mips/ralink/early_printk.c
index b46d041..255d695 100644
--- a/arch/mips/ralink/early_printk.c
+++ b/arch/mips/ralink/early_printk.c
@@ -12,21 +12,24 @@
#include <asm/addrspace.h>

#ifdef CONFIG_SOC_RT288X
-#define EARLY_UART_BASE 0x300c00
+#define EARLY_UART_BASE 0x300c00
+#define CHIPID_BASE 0x300004
+#elif defined(CONFIG_SOC_MT7621)
+#define EARLY_UART_BASE 0x1E000c00
+#define CHIPID_BASE 0x1E000004
#else
-#define EARLY_UART_BASE 0x10000c00
+#define EARLY_UART_BASE 0x10000c00
+#define CHIPID_BASE 0x10000004
#endif

-#define UART_REG_RX 0x00
-#define UART_REG_TX 0x04
-#define UART_REG_IER 0x08
-#define UART_REG_IIR 0x0c
-#define UART_REG_FCR 0x10
-#define UART_REG_LCR 0x14
-#define UART_REG_MCR 0x18
-#define UART_REG_LSR 0x1c
+#define MT7628_CHIP_NAME1 0x20203832
+
+#define UART_REG_TX 0x04
+#define UART_REG_LSR 0x14
+#define UART_REG_LSR_RT2880 0x1c

static __iomem void *uart_membase = (__iomem void *) KSEG1ADDR(EARLY_UART_BASE);
+static __iomem void *chipid_membase = (__iomem void *) KSEG1ADDR(CHIPID_BASE);

static inline void uart_w32(u32 val, unsigned reg)
{
@@ -38,11 +41,23 @@ static inline u32 uart_r32(unsigned reg)
return __raw_readl(uart_membase + reg);
}

+static inline int soc_is_mt7628(void)
+{
+ return IS_ENABLED(CONFIG_SOC_MT7620) &&
+ (__raw_readl(chipid_membase) == MT7628_CHIP_NAME1);
+}
+
void prom_putchar(unsigned char ch)
{
- while ((uart_r32(UART_REG_LSR) & UART_LSR_THRE) == 0)
- ;
- uart_w32(ch, UART_REG_TX);
- while ((uart_r32(UART_REG_LSR) & UART_LSR_THRE) == 0)
- ;
+ if (IS_ENABLED(CONFIG_SOC_MT7621) || soc_is_mt7628()) {
+ uart_w32(ch, UART_TX);
+ while ((uart_r32(UART_REG_LSR) & UART_LSR_THRE) == 0)
+ ;
+ } else {
+ while ((uart_r32(UART_REG_LSR_RT2880) & UART_LSR_THRE) == 0)
+ ;
+ uart_w32(ch, UART_REG_TX);
+ while ((uart_r32(UART_REG_LSR_RT2880) & UART_LSR_THRE) == 0)
+ ;
+ }
}

[John Crispin]

Signed-off-by: John Crispin <***@openwrt.org>
---
arch/mips/ralink/irq.c | 34 ++++++++++++++++++++++++----------
1 file changed, 24 insertions(+), 10 deletions(-)

diff --git a/arch/mips/ralink/irq.c b/arch/mips/ralink/irq.c
index 781b3d1..62ad64b 100644
--- a/arch/mips/ralink/irq.c
+++ b/arch/mips/ralink/irq.c
@@ -20,14 +20,6 @@

#include "common.h"

-/* INTC register offsets */
-#define INTC_REG_STATUS0 0x00
-#define INTC_REG_STATUS1 0x04
-#define INTC_REG_TYPE 0x20
-#define INTC_REG_RAW_STATUS 0x30
-#define INTC_REG_ENABLE 0x34
-#define INTC_REG_DISABLE 0x38
-
#define INTC_INT_GLOBAL BIT(31)

#define RALINK_CPU_IRQ_INTC (MIPS_CPU_IRQ_BASE + 2)
@@ -44,16 +36,34 @@

#define RALINK_INTC_IRQ_PERFC (RALINK_INTC_IRQ_BASE + 9)

+enum rt_intc_regs_enum {
+ INTC_REG_STATUS0 = 0,
+ INTC_REG_STATUS1,
+ INTC_REG_TYPE,
+ INTC_REG_RAW_STATUS,
+ INTC_REG_ENABLE,
+ INTC_REG_DISABLE,
+};
+
+static u32 rt_intc_regs[] = {
+ [INTC_REG_STATUS0] = 0x00,
+ [INTC_REG_STATUS1] = 0x04,
+ [INTC_REG_TYPE] = 0x20,
+ [INTC_REG_RAW_STATUS] = 0x30,
+ [INTC_REG_ENABLE] = 0x34,
+ [INTC_REG_DISABLE] = 0x38,
+};
+
static void __iomem *rt_intc_membase;

static inline void rt_intc_w32(u32 val, unsigned reg)
{
- __raw_writel(val, rt_intc_membase + reg);
+ __raw_writel(val, rt_intc_membase + rt_intc_regs[reg]);
}

static inline u32 rt_intc_r32(unsigned reg)
{
- return __raw_readl(rt_intc_membase + reg);
+ return __raw_readl(rt_intc_membase + rt_intc_regs[reg]);
}

static void ralink_intc_irq_unmask(struct irq_data *d)
@@ -134,6 +144,10 @@ static int __init intc_of_init(struct device_node *node,
struct irq_domain *domain;
int irq;

+ if (!of_property_read_u32_array(node, "ralink,intc-registers",
+ rt_intc_regs, 6))
+ pr_info("intc: using register map from devicetree\n");
+
irq = irq_of_parse_and_map(node, 0);
if (!irq)
panic("Failed to get INTC IRQ");

[John Crispin]

This is the small version of MT7620a.

Signed-off-by: John Crispin <***@openwrt.org>
---
arch/mips/include/asm/mach-ralink/mt7620.h | 7 ++-----
arch/mips/ralink/mt7620.c | 20 +++++++++++++-------
2 files changed, 15 insertions(+), 12 deletions(-)

diff --git a/arch/mips/include/asm/mach-ralink/mt7620.h b/arch/mips/include/asm/mach-ralink/mt7620.h
index a05c14c2..863aea5 100644
--- a/arch/mips/include/asm/mach-ralink/mt7620.h
+++ b/arch/mips/include/asm/mach-ralink/mt7620.h
@@ -25,11 +25,8 @@
#define SYSC_REG_CPLL_CONFIG0 0x54
#define SYSC_REG_CPLL_CONFIG1 0x58

-#define MT7620N_CHIP_NAME0 0x33365452
-#define MT7620N_CHIP_NAME1 0x20203235
-
-#define MT7620A_CHIP_NAME0 0x3637544d
-#define MT7620A_CHIP_NAME1 0x20203032
+#define MT7620_CHIP_NAME0 0x3637544d
+#define MT7620_CHIP_NAME1 0x20203032

#define SYSCFG0_XTAL_FREQ_SEL BIT(6)

diff --git a/arch/mips/ralink/mt7620.c b/arch/mips/ralink/mt7620.c
index 24fb40a..e4b1f82 100644
--- a/arch/mips/ralink/mt7620.c
+++ b/arch/mips/ralink/mt7620.c
@@ -277,6 +277,7 @@ void __init ralink_clk_init(void)
ralink_clk_add("10000500.uart", periph_rate);
ralink_clk_add("10000b00.spi", sys_rate);
ralink_clk_add("10000c00.uartlite", periph_rate);
+ ralink_clk_add("10180000.wmac", xtal_rate);
}

void __init ralink_of_remap(void)
@@ -298,22 +299,27 @@ void prom_soc_init(struct ralink_soc_info *soc_info)
u32 cfg0;
u32 pmu0;
u32 pmu1;
+ u32 bga;

n0 = __raw_readl(sysc + SYSC_REG_CHIP_NAME0);
n1 = __raw_readl(sysc + SYSC_REG_CHIP_NAME1);
+ rev = __raw_readl(sysc + SYSC_REG_CHIP_REV);
+ bga = (rev >> CHIP_REV_PKG_SHIFT) & CHIP_REV_PKG_MASK;

- if (n0 == MT7620N_CHIP_NAME0 && n1 == MT7620N_CHIP_NAME1) {
- name = "MT7620N";
- soc_info->compatible = "ralink,mt7620n-soc";
- } else if (n0 == MT7620A_CHIP_NAME0 && n1 == MT7620A_CHIP_NAME1) {
+ if (n0 != MT7620_CHIP_NAME0 || n1 != MT7620_CHIP_NAME1)
+ panic("mt7620: unknown SoC, n0:%08x n1:%08x\n", n0, n1);
+
+ if (bga) {
name = "MT7620A";
soc_info->compatible = "ralink,mt7620a-soc";
} else {
- panic("mt7620: unknown SoC, n0:%08x n1:%08x", n0, n1);
+ name = "MT7620N";
+ soc_info->compatible = "ralink,mt7620n-soc";
+#ifdef CONFIG_PCI
+ panic("mt7620n is only supported for non pci kernels");
+#endif
}

- rev = __raw_readl(sysc + SYSC_REG_CHIP_REV);
-
snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
"Ralink %s ver:%u eco:%u",
name,

[Sergei Shtylyov]

Hello.

Post by John Crispin
This is the small version of MT7620a.
---
arch/mips/include/asm/mach-ralink/mt7620.h | 7 ++-----
arch/mips/ralink/mt7620.c | 20 +++++++++++++-------
2 files changed, 15 insertions(+), 12 deletions(-)

[...]

Post by John Crispin
diff --git a/arch/mips/ralink/mt7620.c b/arch/mips/ralink/mt7620.c
index 24fb40a..e4b1f82 100644
--- a/arch/mips/ralink/mt7620.c
+++ b/arch/mips/ralink/mt7620.c

[...]

Post by John Crispin
@@ -298,22 +299,27 @@ void prom_soc_init(struct ralink_soc_info *soc_info)
u32 cfg0;
u32 pmu0;
u32 pmu1;
+ u32 bga;
n0 = __raw_readl(sysc + SYSC_REG_CHIP_NAME0);
n1 = __raw_readl(sysc + SYSC_REG_CHIP_NAME1);
+ rev = __raw_readl(sysc + SYSC_REG_CHIP_REV);
+ bga = (rev >> CHIP_REV_PKG_SHIFT) & CHIP_REV_PKG_MASK;
- if (n0 == MT7620N_CHIP_NAME0 && n1 == MT7620N_CHIP_NAME1) {
- name = "MT7620N";
- soc_info->compatible = "ralink,mt7620n-soc";
- } else if (n0 == MT7620A_CHIP_NAME0 && n1 == MT7620A_CHIP_NAME1) {
+ if (n0 != MT7620_CHIP_NAME0 || n1 != MT7620_CHIP_NAME1)
+ panic("mt7620: unknown SoC, n0:%08x n1:%08x\n", n0, n1);
+
+ if (bga) {
name = "MT7620A";
soc_info->compatible = "ralink,mt7620a-soc";
} else {
- panic("mt7620: unknown SoC, n0:%08x n1:%08x", n0, n1);
+ name = "MT7620N";
+ soc_info->compatible = "ralink,mt7620n-soc";
+#ifdef CONFIG_PCI

I suggest:

if (IS_ENABLED(CONFIG_PCI))

in order to avoid this #ifdef.

[...]

WBR, Sergei

[John Crispin]

Post by Sergei Shtylyov

+ if (bga) { name = "MT7620A"; soc_info->compatible =
"ralink,mt7620a-soc"; } else { - panic("mt7620: unknown
SoC, n0:%08x n1:%08x", n0, n1); + name = "MT7620N"; +
soc_info->compatible = "ralink,mt7620n-soc"; +#ifdef CONFIG_PCI

if (IS_ENABLED(CONFIG_PCI))
in order to avoid this #ifdef.
[...]
WBR, Sergei

yep, holds true fo the irq-gic.c patch where i also use ifdef. I'll
fix and resend the 2 patches.

John

[John Crispin]

Signed-off-by: John Crispin <***@openwrt.org>
---
arch/mips/include/asm/mach-ralink/mt7620.h | 11 ++
arch/mips/ralink/Kconfig | 2 +-
arch/mips/ralink/mt7620.c | 276 +++++++++++++++++++++++-----
3 files changed, 243 insertions(+), 46 deletions(-)

diff --git a/arch/mips/include/asm/mach-ralink/mt7620.h b/arch/mips/include/asm/mach-ralink/mt7620.h
index 863aea5..1976fb8 100644
--- a/arch/mips/include/asm/mach-ralink/mt7620.h
+++ b/arch/mips/include/asm/mach-ralink/mt7620.h
@@ -13,6 +13,13 @@
#ifndef _MT7620_REGS_H_
#define _MT7620_REGS_H_

+enum mt762x_soc_type {
+ MT762X_SOC_UNKNOWN = 0,
+ MT762X_SOC_MT7620A,
+ MT762X_SOC_MT7620N,
+ MT762X_SOC_MT7628AN,
+};
+
#define MT7620_SYSC_BASE 0x10000000

#define SYSC_REG_CHIP_NAME0 0x00
@@ -27,6 +34,7 @@

#define MT7620_CHIP_NAME0 0x3637544d
#define MT7620_CHIP_NAME1 0x20203032
+#define MT7628_CHIP_NAME1 0x20203832

#define SYSCFG0_XTAL_FREQ_SEL BIT(6)

@@ -71,6 +79,9 @@
#define SYSCFG0_DRAM_TYPE_DDR1 1
#define SYSCFG0_DRAM_TYPE_DDR2 2

+#define SYSCFG0_DRAM_TYPE_DDR2_MT7628 0
+#define SYSCFG0_DRAM_TYPE_DDR1_MT7628 1
+
#define MT7620_DRAM_BASE 0x0
#define MT7620_SDRAM_SIZE_MIN 2
#define MT7620_SDRAM_SIZE_MAX 64
diff --git a/arch/mips/ralink/Kconfig b/arch/mips/ralink/Kconfig
index 4a29665..cfd0e54 100644
--- a/arch/mips/ralink/Kconfig
+++ b/arch/mips/ralink/Kconfig
@@ -26,7 +26,7 @@ choice
select HW_HAS_PCI

config SOC_MT7620
- bool "MT7620"
+ bool "MT7620/8"

endchoice

diff --git a/arch/mips/ralink/mt7620.c b/arch/mips/ralink/mt7620.c
index e4b1f82..2ea5ff6 100644
--- a/arch/mips/ralink/mt7620.c
+++ b/arch/mips/ralink/mt7620.c
@@ -37,6 +37,9 @@
#define PMU1_CFG 0x8C
#define DIG_SW_SEL BIT(25)

+/* is this a MT7620 or a MT7628 */
+enum mt762x_soc_type mt762x_soc;
+
/* does the board have sdram or ddram */
static int dram_type;

@@ -94,6 +97,136 @@ static struct rt2880_pmx_group mt7620a_pinmux_data[] = {
{ 0 }
};

+static struct rt2880_pmx_func pwm1_grp_mt7628[] = {
+ FUNC("sdcx", 3, 19, 1),
+ FUNC("utif", 2, 19, 1),
+ FUNC("gpio", 1, 19, 1),
+ FUNC("pwm", 0, 19, 1),
+};
+
+static struct rt2880_pmx_func pwm0_grp_mt7628[] = {
+ FUNC("sdcx", 3, 18, 1),
+ FUNC("utif", 2, 18, 1),
+ FUNC("gpio", 1, 18, 1),
+ FUNC("pwm", 0, 18, 1),
+};
+
+static struct rt2880_pmx_func uart2_grp_mt7628[] = {
+ FUNC("sdcx", 3, 20, 2),
+ FUNC("pwm", 2, 20, 2),
+ FUNC("gpio", 1, 20, 2),
+ FUNC("uart", 0, 20, 2),
+};
+
+static struct rt2880_pmx_func uart1_grp_mt7628[] = {
+ FUNC("sdcx", 3, 45, 2),
+ FUNC("pwm", 2, 45, 2),
+ FUNC("gpio", 1, 45, 2),
+ FUNC("uart", 0, 45, 2),
+};
+
+static struct rt2880_pmx_func i2c_grp_mt7628[] = {
+ FUNC("-", 3, 4, 2),
+ FUNC("debug", 2, 4, 2),
+ FUNC("gpio", 1, 4, 2),
+ FUNC("i2c", 0, 4, 2),
+};
+
+static struct rt2880_pmx_func refclk_grp_mt7628[] = { FUNC("reclk", 0, 36, 1) };
+static struct rt2880_pmx_func perst_grp_mt7628[] = { FUNC("perst", 0, 37, 1) };
+static struct rt2880_pmx_func wdt_grp_mt7628[] = { FUNC("wdt", 0, 15, 38) };
+static struct rt2880_pmx_func spi_grp_mt7628[] = { FUNC("spi", 0, 7, 4) };
+
+static struct rt2880_pmx_func sd_mode_grp_mt7628[] = {
+ FUNC("jtag", 3, 22, 8),
+ FUNC("utif", 2, 22, 8),
+ FUNC("gpio", 1, 22, 8),
+ FUNC("sdcx", 0, 22, 8),
+};
+
+static struct rt2880_pmx_func uart0_grp_mt7628[] = {
+ FUNC("-", 3, 12, 2),
+ FUNC("-", 2, 12, 2),
+ FUNC("gpio", 1, 12, 2),
+ FUNC("uart", 0, 12, 2),
+};
+
+static struct rt2880_pmx_func i2s_grp_mt7628[] = {
+ FUNC("antenna", 3, 0, 4),
+ FUNC("pcm", 2, 0, 4),
+ FUNC("gpio", 1, 0, 4),
+ FUNC("i2s", 0, 0, 4),
+};
+
+static struct rt2880_pmx_func spi_cs1_grp_mt7628[] = {
+ FUNC("-", 3, 6, 1),
+ FUNC("refclk", 2, 6, 1),
+ FUNC("gpio", 1, 6, 1),
+ FUNC("spi", 0, 6, 1),
+};
+
+static struct rt2880_pmx_func spis_grp_mt7628[] = {
+ FUNC("pwm", 3, 14, 4),
+ FUNC("util", 2, 14, 4),
+ FUNC("gpio", 1, 14, 4),
+ FUNC("spis", 0, 14, 4),
+};
+
+static struct rt2880_pmx_func gpio_grp_mt7628[] = {
+ FUNC("pcie", 3, 11, 1),
+ FUNC("refclk", 2, 11, 1),
+ FUNC("gpio", 1, 11, 1),
+ FUNC("gpio", 0, 11, 1),
+};
+
+#define MT7628_GPIO_MODE_MASK 0x3
+
+#define MT7628_GPIO_MODE_PWM1 30
+#define MT7628_GPIO_MODE_PWM0 28
+#define MT7628_GPIO_MODE_UART2 26
+#define MT7628_GPIO_MODE_UART1 24
+#define MT7628_GPIO_MODE_I2C 20
+#define MT7628_GPIO_MODE_REFCLK 18
+#define MT7628_GPIO_MODE_PERST 16
+#define MT7628_GPIO_MODE_WDT 14
+#define MT7628_GPIO_MODE_SPI 12
+#define MT7628_GPIO_MODE_SDMODE 10
+#define MT7628_GPIO_MODE_UART0 8
+#define MT7628_GPIO_MODE_I2S 6
+#define MT7628_GPIO_MODE_CS1 4
+#define MT7628_GPIO_MODE_SPIS 2
+#define MT7628_GPIO_MODE_GPIO 0
+
+static struct rt2880_pmx_group mt7628an_pinmux_data[] = {
+ GRP_G("pmw1", pwm1_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_PWM1),
+ GRP_G("pmw1", pwm0_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_PWM0),
+ GRP_G("uart2", uart2_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_UART2),
+ GRP_G("uart1", uart1_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_UART1),
+ GRP_G("i2c", i2c_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_I2C),
+ GRP("refclk", refclk_grp_mt7628, 1, MT7628_GPIO_MODE_REFCLK),
+ GRP("perst", perst_grp_mt7628, 1, MT7628_GPIO_MODE_PERST),
+ GRP("wdt", wdt_grp_mt7628, 1, MT7628_GPIO_MODE_WDT),
+ GRP("spi", spi_grp_mt7628, 1, MT7628_GPIO_MODE_SPI),
+ GRP_G("sdmode", sd_mode_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_SDMODE),
+ GRP_G("uart0", uart0_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_UART0),
+ GRP_G("i2s", i2s_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_I2S),
+ GRP_G("spi cs1", spi_cs1_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_CS1),
+ GRP_G("spis", spis_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_SPIS),
+ GRP_G("gpio", gpio_grp_mt7628, MT7628_GPIO_MODE_MASK,
+ 1, MT7628_GPIO_MODE_GPIO),
+ { 0 }
+};
+
static __init u32
mt7620_calc_rate(u32 ref_rate, u32 mul, u32 div)
{
@@ -244,29 +377,42 @@ void __init ralink_clk_init(void)

xtal_rate = mt7620_get_xtal_rate();

- cpu_pll_rate = mt7620_get_cpu_pll_rate(xtal_rate);
- pll_rate = mt7620_get_pll_rate(xtal_rate, cpu_pll_rate);
-
- cpu_rate = mt7620_get_cpu_rate(pll_rate);
- dram_rate = mt7620_get_dram_rate(pll_rate);
- sys_rate = mt7620_get_sys_rate(cpu_rate);
- periph_rate = mt7620_get_periph_rate(xtal_rate);
-
#define RFMT(label) label ":%lu.%03luMHz "
#define RINT(x) ((x) / 1000000)
#define RFRAC(x) (((x) / 1000) % 1000)

- pr_debug(RFMT("XTAL") RFMT("CPU_PLL") RFMT("PLL"),
- RINT(xtal_rate), RFRAC(xtal_rate),
- RINT(cpu_pll_rate), RFRAC(cpu_pll_rate),
- RINT(pll_rate), RFRAC(pll_rate));
+ if (mt762x_soc == MT762X_SOC_MT7628AN) {
+ if (xtal_rate == MHZ(40))
+ cpu_rate = MHZ(580);
+ else
+ cpu_rate = MHZ(575);
+ dram_rate = sys_rate = cpu_rate / 3;
+ periph_rate = MHZ(40);
+
+ ralink_clk_add("10000d00.uartlite", periph_rate);
+ ralink_clk_add("10000e00.uartlite", periph_rate);
+ } else {
+ cpu_pll_rate = mt7620_get_cpu_pll_rate(xtal_rate);
+ pll_rate = mt7620_get_pll_rate(xtal_rate, cpu_pll_rate);
+
+ cpu_rate = mt7620_get_cpu_rate(pll_rate);
+ dram_rate = mt7620_get_dram_rate(pll_rate);
+ sys_rate = mt7620_get_sys_rate(cpu_rate);
+ periph_rate = mt7620_get_periph_rate(xtal_rate);
+
+ pr_debug(RFMT("XTAL") RFMT("CPU_PLL") RFMT("PLL"),
+ RINT(xtal_rate), RFRAC(xtal_rate),
+ RINT(cpu_pll_rate), RFRAC(cpu_pll_rate),
+ RINT(pll_rate), RFRAC(pll_rate));
+
+ ralink_clk_add("10000500.uart", periph_rate);
+ }

pr_debug(RFMT("CPU") RFMT("DRAM") RFMT("SYS") RFMT("PERIPH"),
RINT(cpu_rate), RFRAC(cpu_rate),
RINT(dram_rate), RFRAC(dram_rate),
RINT(sys_rate), RFRAC(sys_rate),
RINT(periph_rate), RFRAC(periph_rate));
-
#undef RFRAC
#undef RINT
#undef RFMT
@@ -274,7 +420,6 @@ void __init ralink_clk_init(void)
ralink_clk_add("cpu", cpu_rate);
ralink_clk_add("10000100.timer", periph_rate);
ralink_clk_add("10000120.watchdog", periph_rate);
- ralink_clk_add("10000500.uart", periph_rate);
ralink_clk_add("10000b00.spi", sys_rate);
ralink_clk_add("10000c00.uartlite", periph_rate);
ralink_clk_add("10180000.wmac", xtal_rate);
@@ -289,6 +434,52 @@ void __init ralink_of_remap(void)
panic("Failed to remap core resources");
}

+static __init void
+mt7620_dram_init(struct ralink_soc_info *soc_info)
+{
+ switch (dram_type) {
+ case SYSCFG0_DRAM_TYPE_SDRAM:
+ pr_info("Board has SDRAM\n");
+ soc_info->mem_size_min = MT7620_SDRAM_SIZE_MIN;
+ soc_info->mem_size_max = MT7620_SDRAM_SIZE_MAX;
+ break;
+
+ case SYSCFG0_DRAM_TYPE_DDR1:
+ pr_info("Board has DDR1\n");
+ soc_info->mem_size_min = MT7620_DDR1_SIZE_MIN;
+ soc_info->mem_size_max = MT7620_DDR1_SIZE_MAX;
+ break;
+
+ case SYSCFG0_DRAM_TYPE_DDR2:
+ pr_info("Board has DDR2\n");
+ soc_info->mem_size_min = MT7620_DDR2_SIZE_MIN;
+ soc_info->mem_size_max = MT7620_DDR2_SIZE_MAX;
+ break;
+ default:
+ BUG();
+ }
+}
+
+static __init void
+mt7628_dram_init(struct ralink_soc_info *soc_info)
+{
+ switch (dram_type) {
+ case SYSCFG0_DRAM_TYPE_DDR1_MT7628:
+ pr_info("Board has DDR1\n");
+ soc_info->mem_size_min = MT7620_DDR1_SIZE_MIN;
+ soc_info->mem_size_max = MT7620_DDR1_SIZE_MAX;
+ break;
+
+ case SYSCFG0_DRAM_TYPE_DDR2_MT7628:
+ pr_info("Board has DDR2\n");
+ soc_info->mem_size_min = MT7620_DDR2_SIZE_MIN;
+ soc_info->mem_size_max = MT7620_DDR2_SIZE_MAX;
+ break;
+ default:
+ BUG();
+ }
+}
+
void prom_soc_init(struct ralink_soc_info *soc_info)
{
void __iomem *sysc = (void __iomem *) KSEG1ADDR(MT7620_SYSC_BASE);
@@ -306,18 +497,25 @@ void prom_soc_init(struct ralink_soc_info *soc_info)
rev = __raw_readl(sysc + SYSC_REG_CHIP_REV);
bga = (rev >> CHIP_REV_PKG_SHIFT) & CHIP_REV_PKG_MASK;

- if (n0 != MT7620_CHIP_NAME0 || n1 != MT7620_CHIP_NAME1)
- panic("mt7620: unknown SoC, n0:%08x n1:%08x\n", n0, n1);
-
- if (bga) {
- name = "MT7620A";
- soc_info->compatible = "ralink,mt7620a-soc";
- } else {
- name = "MT7620N";
- soc_info->compatible = "ralink,mt7620n-soc";
+ if (n0 == MT7620_CHIP_NAME0 && n1 == MT7620_CHIP_NAME1) {
+ if (bga) {
+ mt762x_soc = MT762X_SOC_MT7620A;
+ name = "MT7620A";
+ soc_info->compatible = "ralink,mt7620a-soc";
+ } else {
+ mt762x_soc = MT762X_SOC_MT7620N;
+ name = "MT7620N";
+ soc_info->compatible = "ralink,mt7620n-soc";
#ifdef CONFIG_PCI
- panic("mt7620n is only supported for non pci kernels");
+ panic("mt7620n is only supported for non pci kernels");
#endif
+ }
+ } else if (n0 == MT7620_CHIP_NAME0 && n1 == MT7628_CHIP_NAME1) {
+ mt762x_soc = MT762X_SOC_MT7628AN;
+ name = "MT7628AN";
+ soc_info->compatible = "ralink,mt7628an-soc";
+ } else {
+ panic("mt762x: unknown SoC, n0:%08x n1:%08x\n", n0, n1);
}

snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
@@ -329,28 +527,11 @@ void prom_soc_init(struct ralink_soc_info *soc_info)
cfg0 = __raw_readl(sysc + SYSC_REG_SYSTEM_CONFIG0);
dram_type = (cfg0 >> SYSCFG0_DRAM_TYPE_SHIFT) & SYSCFG0_DRAM_TYPE_MASK;

- switch (dram_type) {
- case SYSCFG0_DRAM_TYPE_SDRAM:
- pr_info("Board has SDRAM\n");
- soc_info->mem_size_min = MT7620_SDRAM_SIZE_MIN;
- soc_info->mem_size_max = MT7620_SDRAM_SIZE_MAX;
- break;
-
- case SYSCFG0_DRAM_TYPE_DDR1:
- pr_info("Board has DDR1\n");
- soc_info->mem_size_min = MT7620_DDR1_SIZE_MIN;
- soc_info->mem_size_max = MT7620_DDR1_SIZE_MAX;
- break;
-
- case SYSCFG0_DRAM_TYPE_DDR2:
- pr_info("Board has DDR2\n");
- soc_info->mem_size_min = MT7620_DDR2_SIZE_MIN;
- soc_info->mem_size_max = MT7620_DDR2_SIZE_MAX;
- break;
- default:
- BUG();
- }
soc_info->mem_base = MT7620_DRAM_BASE;
+ if (mt762x_soc == MT762X_SOC_MT7628AN)
+ mt7628_dram_init(soc_info);
+ else
+ mt7620_dram_init(soc_info);

pmu0 = __raw_readl(sysc + PMU0_CFG);
pmu1 = __raw_readl(sysc + PMU1_CFG);
@@ -359,4 +540,9 @@ void prom_soc_init(struct ralink_soc_info *soc_info)
(pmu0 & PMU_SW_SET) ? ("sw") : ("hw"));
pr_info("Digital PMU set to %s control\n",
(pmu1 & DIG_SW_SEL) ? ("sw") : ("hw"));
+
+ if (mt762x_soc == MT762X_SOC_MT7628AN)
+ rt2880_pinmux_data = mt7628an_pinmux_data;
+ else
+ rt2880_pinmux_data = mt7620a_pinmux_data;
}